rdlc qr code

rdlc qr code

rdlc qr code

rdlc qr code

rdlc qr code

rdlc qr code,
rdlc qr code,

rdlc qr code,
rdlc qr code,
rdlc qr code,

rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,

rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,
rdlc qr code,

involves starting your computer using the Vista media and interrupting the normal installation to access diskpartexe to partition and format your volumes If the target drive has an operating system installed, do not perform this procedure Instead, you will need to repartition the drive, as discussed in the following section To partition a drive with no operating system for BitLocker Drive Encryption: 1 While installing Vista, enter Setup: a Turn on the computer with the Vista installation media in the CD-ROM or DVD-ROM drive When prompted, press any key to boot from the Vista installation media b After Vista mounts the Setup environment, the Installation Windows dialog box appears In the dialog box, choose System Recovery Options c Clear any operating systems listed in the System Recovery Options list, and then click Next d Click Command Line Window In the command-line window, type diskpartexe 2 Create the BitLocker Partition: a Select the hard disk for use by typing select disk 0, and then erase the existing partition table by typing clean b Create a primary partition by typing create partition primary Set the drive letter by typing assign letter=C c Format the partition by typing Format FS=NTFS QUICK Then set the minimum partition size to 450 MB by typing Shrink minimum=450 NOTE If Vista is already installed, you can use Compmgmtmsc to access the Disk Management Console and accomplish the same tasks 3 Create the system partition: a After the Shrink command completes for the C volume, create a primary partition in the space remaining by typing Create partition primary b Set the new partition as active by typing Active c Set the drive letter by typing assign letter=D You can use drive letters other than D if you need to d Format the new partition by typing Format FS=NTFS QUICK 4 Quit the Diskpart application by typing exit Close the Command Prompt window by typing exit.

Mike Meyers CompTIA A+ Guide: PC Technician (Exams 220-602, 220-603, & 220-604)

Listing 3-4

10:

Second, make sure you have room for the drive in the case Where will you place it Do you have a spare power connector Will the data and power cables reach the drive A quick test fit is always a good idea Don t worry about PIO Modes and DMA a new drive will support anything your controller wants to do

.

5 Restart the computer and then press any key to boot from the installation media when prompted Select Install Now, accept the license agreement, and proceed with the installation Install Vista on drive C 6 If the computer BIOS is TPM 12 compliant and TPM module is active, you will need to initialize it as described in the Initializing the TPM section later in this chapter

Cashier cashr = new Cashier(); cashrFirstName = "May";